Variable-rate crop protection
Variable rate herbicide application: spray the weed patches, not the whole field
Map weed patches and thin canopy from satellite imagery, turn them into an on/off prescription map or one with two application rates, and load it on your sprayer’s terminal. Section control switches the boom; you pay for the product the patches need.
✓Weed patches mapped from imagery
✓Prescription maps: spray or skip, or two doses
✓Ready for ISOBUS and John Deere terminals
Independent of input sellers, and your farm data stays yours
30-day trial on up to 250 acres (101 ha), no card required
45.9 %of a 311-acre field left unsprayed in one herbicide pass, 185.6 L of product saved
Patch spraying planner
How much of a field your sprayer can leave dry
A 21.6-hectare sample field with weed patches and a weedy headland, at your field size, product rate, price and boom.
Patches and boom
Section width
Canopy and application rates
Boom 36 m120 ft, switching every 3 m10 ft of travel
28 %of the field sprayedless product than one uniform application rate
91.0 Lproduct on your field
229 Lproduct saved against a flat pass
€2,519saved on this pass
Where the sprayed area comes from
Share of the field sprayed, by section width
Product on the field = label rate × sprayed area; a flat pass = label rate × the whole field. Patches keep the full label rate. Weeds grow in patches rather than evenly (Cardina, Johnson and Sparrow, Weed Science, 1997), which is what patch spraying from maps relies on (Gerhards and Oebel, Weed Research, 2006).
Product on the field = full application rate × dense area + reduced application rate × thinner area. The application rate changes along the pass for the whole boom, every 3 m10 ft. Fungicide dose matched to canopy density: Dammer, Thöle, Volk and Hau, Precision Agriculture, 2009. Keep both application rates inside the label range.
A real prescription
311 acres, one herbicide pass, 46 % of the field left dry
A post-emergence pass planned in GeoPard from a single vegetation index image. The patches got the full 1.3 L per acre; the clean ground got nothing.
| Field | 311.3 ac |
|---|---|
| Unsprayed zone | 142.8 ac45.9 % of the field |
| Sprayed zone | 168.5 acat 1.3 L/ac |
| Flat pass | 404.7 L311.3 ac × 1.3 L/ac |
| Prescription | 219.1 L168.5 ac × 1.3 L/ac |
| Product saved | 185.6 L404.7 L − 219.1 L |
| Saved at $12.00/L | $2,228185.6 L × $12.00 |
In GeoPard
From satellite image to the sprayer’s terminal
Pick the image
Sentinel-2 every few days, or Planet at 3 m every day for small patches. Soil-adjusted indices such as OSAVI separate green weeds from bare soil before the crop closes; red-edge indices work later in the season.
›Tutorial: indices for crops and soilsMap the patches
Split the image into a sprayed and an unsprayed zone, then merge, split or redraw any patch you know better from the field.
›Tutorial: weed patches and herbicide prescriptionWrite your own rule
For a rule of your own, such as spraying only where the index rose since last week’s image, write it as a formula and the map comes back from it.
›Tutorial: equation-based mapsSet the application rates
Zero on the clean ground and the label rate in the patches, or two application rates by canopy for fungicide and desiccant. The table totals the product to load for the field.
›Tutorial: application rates by zoneLoad it on the terminal
Download ISOXML for an ISOBUS terminal or a shapefile with a numeric application rate, or send the prescription to John Deere Operations Center as a work plan.
›Tutorial: ISOXML export›Tutorial: John Deere work plansCheck what went on
Bring the as-applied or See & Spray data back from Operations Center and set it against the map, with the same formulas, to find the patches that return next season.
›Tutorial: See & Spray data
Who does what
✓GeoPard maps the patches, builds the prescription and writes the file.
✓Your terminal and its section control switch the boom in the field.
✓After the pass, GeoPard reads the as-applied data back for the next decision.
Field-tested settings
Settings that hold up in the field
Index
OSAVI until the canopy closes, then a red-edge index from the 6 to 9 leaf stage.
Smallest patch
Skip patches smaller than about twice a section’s footprint: around 72 m² for 3 m sections on a 12 m boom.
Edges and buffers
Pull the map 3 to 6 m in from the field edge, and add the no-spray zones the label and local rules require.
Timing
Run the map again 7 to 14 days after emergence to catch escapes in a second pass.
Ground check
Walk three to five of the largest patches before the pass, and keep before and after photos to tune the threshold next time.
Cloud and noise
Pick another date when cloud or shadow crosses the field; for patchy, noisy maps raise the minimum patch size or switch to Planet 3 m imagery.
Agronomists on GeoPard
From people who write prescriptions with it
“Data visualization leads to the creation of ideas and analytics helps us to solve problems. GeoPard’s platform not only helps us visualize data but also gives us the tools to analyze data so we can create solutions and write prescriptions.”
Steve LarocqueOwner of Beyond AgronomyAlberta, Canada“Using Geopard has streamlined key parts of our workflow. In seasons where time is money, we can rely on the team at Geopard to get it done.”
Brendon FriesenOperation and Technology ManagerPointForward, CanadaPricing
What a crop protection prescription costs
Annual covers every field and every prescription. Pay-As-You-Go charges each map once, so a single patch pass costs cents per acre.
Annual
Every field on the farm, all season.
$0.59 per acreper year on the first band (€1.35 per hectare), down to $0.45 (€1.03) as the farm grows
- ✓Unlimited weed maps, prescriptions and formula maps
- ✓Minimum $200 a year (€185)
- ✓One user seat included, extra seats $60 a year
Pay-As-You-Go
A few fields, or the first season of patch spraying.
$20 a month(€19) plus each map you build
- ✓Zones or prescription map: $0.072 per acre (€0.165 per hectare)
- ✓Formula map: $0.10 per acre (€0.229 per hectare)
- ✓Planet 3 m image: $0.08 per acre (€0.183 per hectare)
- ✓Month to month, with no annual commitment
30-day trial
Your own fields, before you pick a plan.
250 acres (101 ha)for 30 days, no card required
- ✓Every analysis feature, including prescriptions and export
- ✓John Deere Operations Center connection
- ✓Nothing is charged when it ends
Billed in USD in acre regions such as the US and Canada, and in EUR everywhere else.